打膠機呈現花膠以及打膠不豐滿的原因
雙組份打膠機出現的很多問題無論是進口的立式打膠機仍是臥式打膠機都會(huì )經常呈現的一種毛病，為了后面更好更順利的進行使用，我們來講講打膠機呈現花膠以及打膠不豐滿的原因。
There are many problems with the two-component sealant dispenser, whether it is an imported vertical sealant dispenser or a horizontal sealant dispenser. In order to use it better and more smoothly, let's talk about the reasons why the sealant dispenser presents the pattern glue and the sealant is not full.
雙組份打膠機呈現花膠：
The two-component glue applicator presents the glue:
1、雙組份打膠機的混膠器內膠體過多固話，阻力增大。
1. There are too many colloids in the mixer of the two-component sealant beater, and the resistance increases.
2、A或B膠膠桶內無膠，膠已用完。
2. There is no glue in A or B glue bucket, and the glue has been used up.
3、A或B膠膠桶內有空氣。
3. There is air in A or B glue bucket.
4、針閥或單向閥阻塞。
4. The needle valve or check valve is blocked.
咱們仔細觀察導致花膠的毛病原因會(huì )發現大多是因為設備沒有定時保護清洗導致的。所以咱們一定要牢記設備一定要定時保護清洗的良好習慣。
If we carefully observe the causes of the problems of the glue, we will find that most of them are caused by the equipment not being protected and cleaned regularly. So we must remember that the equipment must be regularly cleaned to protect the good habit.
雙組份打膠機產生打膠不豐滿：
The two-component gluing machine produces incomplete gluing:
一種狀況是因為咱們將打膠機的打膠速度設置的過快導致的。有的客戶為了加速自己的生產節奏追逐生產計劃，將打膠速度以為調整的過快，導致膠體還沒有達到合格標準機頭就已經移動到下一個位置進行打膠操作了。
One condition is that we set the dispensing speed of the dispensing machine too fast. Some customers chase the production plan in order to speed up their production pace, thinking that the glue filling speed is adjusted too fast, so that the machine head has moved to the next position for glue filling before the glue reaches the qualified standard.
假如咱們需要加速打膠的速度調整了打膠機的移動參數的話，那么咱們對應的也應該對供膠體系也進行相應的設置，比方這時候咱們就需要加大供膠壓力，增大打膠機的出膠速度來配合目標的移動速度的增加。
If we need to speed up the dispensing speed and adjust the movement parameters of the dispensing machine, we should also set the dispensing system accordingly. For example, at this time, we need to increase the dispensing pressure and the dispensing speed of the dispensing machine to match the increase of the moving speed of the target.
假如咱們僅僅是獨自的增加了打膠機的移動速度而沒有對壓力進行調理的話就很有可能呈現打膠不豐滿的狀況發生。另外一種狀況跟打膠機的速度差不多便是咱們的供膠壓力不足導致的。
If we only increase the moving speed of the glue dispenser without regulating the pressure, it is likely that the glue is not full. The other situation is similar to the speed of the glue feeder, which is caused by insufficient glue supply pressure.
除了以上小編說的人為原因導致的這個毛病以外設備的零部件損壞也會(huì )導致這個問題，比方機頭感應器損壞。
In addition to the problem caused by human factors mentioned above, the damage of equipment parts can also cause this problem, for example, the head sensor is damaged.
The reason why the gluing machine presents the flower glue and the gluing is not full is that the content explained above can be used as a reference, and more relevant precautions can be found on our website http://www.xxcyqzj.com After consulting, I learned that!
上一篇：是否選購打膠機您可以從兩方面思考
下一篇：雙組份打膠機機頭不在原位怎么調？
